Automatic Eps Sandwich Panel Roll Forming Machine 0.3-0.6mm Sheet Thickne

equipment for the production sandwich panel eps roll forming machine

Manual Operation: Turn the Automatic Transfer Switch upon the Control Box to the Manual Operation, then the upper right of screen shows that the Manual Operation starts! At this moment,you can easily operate the upper cutter,the down cutter, pressing booster and the saw blade. Press the button that shows the upper cutter should forward, it starts working forward, now you can work the upper and lower blades (advance and retreat), and assist to push the pressing system,and the saw blades. touch the upper blade forward,then the blade began to walk forward, until the position of the down stroke switch stops. if you touch backward,it will began to walk backward,until the position of the up stroke switch stops. the lower blade is the same operation.
The operating of the down cutting is the same as the up cutting. Operation of the pressing material:click the button of the pressing material,the pressure plate is pressed down, and click the button again,the plate is released. Operation of Boosting: Press the button of Boosting, the long cylinder began to inflate, if the trolley is not in situ,the long cylinder will boost it to the place. Saw Blade:Click the button of Saw Blade, it will turn, and click it again,the saw blade will stop.

Current Maintenance
1.After the main machine shutting down, power off the glue pump immediately and dispose properly the glue tank to the glue storage. The glue tank should be cleaned after using it.
2.Loosen handle and hand wheel with compression function in view of after a long period of static pressure, abnormal repression and deformation will occur.
3.Check where glue passes, such as rubber wheels, rollers, hemming wheels, etc. If glue is found, remove it immediately.
4.Clean up the scrap materialof the vacuum system, knives, vacuum cleaners, storage bags and set aside.

Traditional color composite panels generally compound 10 cm thick white polystyrene foam insulation board, the insulation effect is not very good, because the thermal conductivity of polyphenyl foam board is relatively high (thermal conductivity 0.035W / (m · K) above), plus There is a gap between the foam board and the foam board, the leakage temperature is very serious, and the overall actual thermal conductivity is generally higher than 0.05.
New polyurethane spray insulation material can be directly sprayed on the color steel tile, its low thermal conductivity, only 0.022-0.024W / (m · K), insulation effect is 2-3 times that of polystyrene board, is currently all insulation materials in thermal insulation Especially excellent material. Because polyurethanes use direct spray forming technology in construction, the polyurethane foam layer does not form a complete seam impervious to water, which fundamentally eliminates the possibility of deep penetration of roof water along the seam. So as to play a anti-corrosion and waterproof effect.

Our factory was founded in 1998. We have been engaged in the roll forming machine manufacturing industry over 25 years.

Main products are color steel roll forming machine, classical glazed tile forming machine, C/Z purlin roll forming machine, gutter machine, ridge cap machine, keel roll forming machine for light steel structure building, floor deck forming machine, sandwich panel production line, guardrail roll forming line; and various kinds full-automatic cold roll forming line such as cable trey production line, double C bugging rack beam production line; and other roofing machine line, like stone caoted roofing sheet prodction line.

And our factory has more than 15 years of export experience. we already sold to more than 100 countries and regions in the world. We have a deep understanding of the profiles used in each country and provide high-quality suggestions for subsequent customers' purchases.

In the production of machines, from parts processing and welding to assembly, we have strict quality control in every step. We must be responsible to every customer.
we were and continue always keep: "not only complete a machine, but also perfect every detail".

We have approved certification of CE, the concept “control every process and perfect all products” is curved in everyone’s mind. Each machine will be via testing before leaving factory, problem machines will never be delivered to customer.
We have more than 15 years experience of export and know very well about the different needs of customers from both in developing countries and developed countries, and provide a large number of customers with satisfactory design plan. Now our products have been exported to more than100 countries and regions of the world, and established a long-term cooperative relationship with clients. We do firmly believe a true partnership never ends with the delivery of the goods and satisfactory after-sales service can make a great difference.
We are willing to promote the economic and technical exchanges with the world, and do positive work to enhance the friendship between people from different countries. We sincerely hope: you and I hand in hand, create the glorious future altogether!

Choose Cangzhou Huachen Roll Forming Machinery Co.,Ltd is worth your trust.
We manufacture high standard roll forming machine for export for nearly 15 years.

Our machines have been exported to more than 100 countries and regions around the world.
Maintained good cooperative relations with customers.